Skip to content
Lumina Fire & Security

Fire Safety

Fire Alarm Installation from Kent, across the South East

From single-panel conventional systems to fully networked addressable installations, we design, install and commission fire alarm systems that keep people safe and keep you compliant.

Fire Alarms for commercial, public and residential buildings

Conventional, addressable and wireless fire alarm systems designed around your building. Lumina Fire & Security, Kent-based, provides fire alarms work across the South East.

What is included

  • Site survey and system design
  • Conventional, addressable and wireless systems
  • Commissioning and certification
  • User training and handover documentation

Conventional, addressable or wireless: which fire alarm system suits your building?

A conventional system splits the building into zones, so the panel tells you which zone has gone into alarm but not which device. An addressable system gives every detector and call point its own address, so the panel shows the exact location, which saves time in a fire and when tracing faults. Wireless systems use radio devices linked back to the panel, avoiding most cable runs in occupied or finished buildings.

  • Conventional: suits small, simple premises with only a few zones
  • Addressable: suits larger, multi-floor or multi-tenanted buildings
  • Wireless: suits listed interiors, live sites and fast-track installs
  • Hybrid systems mix wired loops with wireless devices where cabling is awkward

BS 5839-1 categories and BS 5839-6 grades explained

Non-domestic buildings are designed to BS 5839-1, which sets a category based on what the system must protect. L categories protect life, from L1 covering the whole building down to L4 covering escape routes only, with L5 for a specific engineered need. P1 and P2 protect property, and category M is manual call points only. Homes and the flats themselves within a block fall under BS 5839-6, which uses grades for the equipment and LD categories for the level of coverage.

  • L1 to L5 for life safety, set by your fire risk assessment
  • P1 for the whole building or P2 for defined high-risk areas
  • Category M where people are always present to raise the alarm
  • BS 5839-6 grades such as D1, D2 and A for dwellings and HMOs

What affects fire alarm installation cost

Every quote depends on the building, so a site survey comes first. The biggest drivers are the system category, which sets how many detectors are needed, and the choice of wired, wireless or addressable equipment. Access, working hours and the finish required in occupied areas also make a real difference, as does linking the alarm to other systems such as AOVs, door holders or lifts.

  • Floor area, number of rooms and the category required
  • Cable routes, containment and whether ceilings are accessible
  • Out-of-hours working in occupied offices, schools or shops
  • Interfaces to sprinklers, AOVs, door release and access control

Which buildings need a fire alarm system?

The Regulatory Reform (Fire Safety) Order 2005 requires the responsible person for most non-domestic premises to make sure there is a suitable way of detecting a fire and warning the people inside. In most offices, shops, warehouses, schools and public buildings, that means an electrical fire alarm system. Houses in multiple occupation and rented homes are covered by housing law and BS 5839-6, while blocks of flats may or may not have a common-area alarm, depending on their fire strategy. How much of the building the system covers, and what type it is, should be set by the fire risk assessment.

  • Offices, shops, warehouses and factories under the Fire Safety Order
  • Schools, surgeries, community buildings and other public premises
  • HMOs and rented homes under housing law and BS 5839-6
  • Common parts of blocks where the fire strategy calls for it

Choosing the right detector for each room

A fire alarm is only as good as its detectors, and the wrong type in the wrong room is behind many false alarms. Optical smoke detectors suit bedrooms, offices and escape routes, where early warning of a slow, smouldering fire matters most. Heat detectors suit kitchens, plant rooms and dusty areas where smoke detection would trigger too easily. Multi-sensor detectors combine smoke and heat sensing to balance speed against false alarms, and optical beam detectors cover tall open spaces such as warehouses, sports halls and atria, where ceiling-mounted heads would be hard to reach and maintain.

  • Optical smoke detection on escape routes and in sleeping areas
  • Fixed-temperature or rate-of-rise heat detection in kitchens and plant rooms
  • Multi-sensors where steam, dust or fumes are occasional
  • Optical beam detectors for high ceilings and large open spaces

How the job works

  1. 1Agree the category and coverageUsing your fire risk assessment and how each floor is occupied, we agree the system category and coverage before design starts, so the quote reflects what the building actually needs.
  2. 2Draw device layouts and a cause-and-effect planDetector, call point and sounder positions are marked on plans, with a cause-and-effect schedule showing what each device triggers, including door releases and other linked systems.
  3. 3Run cables, then fit devices and the panelFire-resistant cabling and containment go in first, then detectors, sounders and the panel are fitted and connected, with each area left safe and tidy for the people using it.
  4. 4Prove the cause and effect, then hand overEach device is activated to prove it reports to the panel and triggers the right outputs, then certificates, as-fitted plans and the logbook are handed over with a run-through of the controls.
Fire Alarm Installation

Fire Alarms: common questions

Who decides which fire alarm category my building needs?

The category should come from your fire risk assessment, which the responsible person for the premises arranges. We read the assessment, look at how the building is used and occupied, and design the system to match. If there is no current assessment, or it does not state a category, we will tell you that before quoting so the design is not based on guesswork.

Is a wireless fire alarm as reliable as a wired one?

A properly designed wireless system meets the same standards for detection as a wired one, and each device is monitored by the panel so a lost signal or weak battery shows as a fault. The trade-off is battery replacement in every device over the life of the system. We carry out a signal survey before recommending wireless, so you know it will work in your building.

Can you replace our old fire alarm panel and keep the existing cabling?

Often, yes. If the existing cable is a suitable fire-resistant type and tests well, a new panel and devices can usually reuse it, which cuts disruption and cost. Where cable is damaged, the wrong type or does not match the new layout, we explain which runs need replacing. A conventional system can also be upgraded to addressable in stages in some buildings.

What paperwork do we get when a new fire alarm is handed over?

You receive the design, installation and commissioning certificates, as-fitted zone or device plans, a logbook and the operating instructions for the panel. We also show your nominated people how to silence, reset and test the system and how to record events in the logbook, because the responsible person needs that information to keep the system maintained.

Get in touch

Talk to an engineer about your building.

Free, no-obligation surveys and quotes for commercial, public and residential properties. Call us or drop us an email and we will get straight back to you.