
Security
Intruder Alarm Call Out from Kent, across the South East
False alarms, faults and panel errors are stressful. Call us and an engineer will attend to diagnose the problem and get your system back to normal.
Alarm Call Out for commercial, public and residential buildings
Alarm going off or showing a fault? We attend to diagnose and fix it. Lumina Fire & Security, Kent-based, provides alarm call out work across the South East.
What is included
- Fault diagnosis on most makes
- False alarm investigation
- Battery and component replacement
- Reset and code changes
Why does a burglar alarm keep going off?
Most repeat false alarms trace back to a handful of causes. A low or failed standby battery can trigger faults or tamper alerts, especially after a power cut. Motion detectors pointed at radiators, heaters or sunny windows react to moving warm air, and loose door contacts open the circuit when a door rattles in the wind. Signalling faults and damaged tamper switches also show up as alarms or panel warnings.
- Low or failed panel, siren or detector batteries
- PIR detectors facing heat sources or draughts
- Misaligned or loose door and window contacts
- Tamper faults from damaged covers or cabling
What to do while you wait for an engineer
If the alarm is sounding and you are the keyholder, first check the property is safe and there is no sign of a break-in; if there is, call the police rather than going in. Note what the keypad says, including any zone number, as this speeds up the repair. Many systems can be silenced with your user code, but do not cut wires or remove panel batteries. This advice applies to intruder alarms only: never silence or switch off a fire alarm.
- Check for signs of entry before going inside
- Write down the zone or fault message shown
- Silence with your user code, not by cutting power
- Never disable a fire alarm or other life-safety system
What happens on an alarm call-out visit
The engineer reads the panel’s event log to see what triggered and when, then tests the suspect zone, battery and signalling path. Many faults can be fixed on the visit by replacing a battery, realigning a contact, moving a detector or swapping a failed part. Where a panel is very old or a part is no longer made, you are told the options before any further work is done.
- Event log read to pinpoint the triggering zone
- Batteries, detectors and contacts tested in turn
- Batteries and common parts replaced on the visit where possible
- Resets and user code changes done before leaving
Repair or replace: when an old alarm is worth fixing
Most call-outs end with a repair, but not every system is worth repeated visits. A panel with a single failed battery, detector or contact is usually straightforward to put right. It becomes a closer decision when faults keep returning across several zones, the panel is obsolete and parts are no longer made, or the engineer code is locked and cannot be reset. In those cases the engineer explains what has failed, what a repair would involve and whether replacing the panel while keeping the existing wiring and detectors is the better use of money. You decide before any further work goes ahead.
- Single failed parts usually repaired on the visit
- Recurring faults across zones point to a wider problem
- Obsolete panels where parts can no longer be sourced
- Replacement options that keep sound wiring and detectors
Stopping false alarms from coming back
Fixing today’s fault is only half the job if the same alarm sounds again next week. After a repair, the engineer looks at why it happened: a detector now facing a new radiator or blind, a door that no longer closes tightly, a battery that was never replaced on time, or users entering their code too slowly after opening the door. Small changes such as moving a detector, adjusting the entry time or fitting a door closer often prevent repeats. Repeated false alarms frustrate neighbours and can cause problems with a monitoring agreement, so preventing them is worth the effort.
- Detectors moved away from new heat sources
- Entry and exit times matched to how the door is used
- Loose doors and contacts tightened or realigned
- Battery replacement dates noted for next time
How the job works
- 1Tell us what the panel showsWhen you call, describe the sound, any keypad or app message and when it happens, so the engineer can bring the parts most likely to be needed.
- 2Diagnose on siteThe engineer reads the event log, tests the zone or device involved and checks the batteries and power supply before recommending a fix.
- 3Repair with your agreementYou are told the cause and the cost of putting it right before chargeable work beyond diagnosis starts, then batteries, parts or settings are replaced.
- 4Reset and confirm it is clearThe system is reset, codes are updated if needed, and the alarm is set and unset with you to confirm the fault has cleared.

Alarm Call Out near you
Local pages with details for the areas we cover most, plus every county and city we work in.
Last reviewed: November 2026
Alarm Call Out: common questions
How do I stop my burglar alarm going off at night?
Night-time false alarms are often caused by a battery that weakens as temperatures drop, a detector reacting to heating coming on, or a door contact moving in the wind. If it happens more than once, note the time and any zone shown on the keypad. Those details point an engineer straight to the cause, which is usually a straightforward repair rather than a new system.
Can you repair a burglar alarm fitted by another company?
Yes, we diagnose faults on most common makes, whoever installed them. The engineer will need access to the panel and, ideally, your user code. If the engineer code is locked by a previous installer, some panels can still be reset; others may need a replacement panel. We explain which situation you are in before carrying out any chargeable work beyond the diagnosis.
Why is my alarm keypad showing a fault or beeping?
Keypad beeps and fault lights usually mean the panel has detected a problem it wants you to know about: a low battery, a mains power loss, a tamper alert, a detector that has stopped reporting or a signalling failure. The keypad or app often shows a code or message. Write it down and mention it when you call, as it narrows down the repair.
Can you change my alarm codes or reset the system?
Yes. We can reset a system after an activation, change or add user codes, remove codes for former staff or tenants and update keyholder details on app-connected systems. Doing this is sensible after moving into a property, when staff leave, or when you are not sure who knows the current code. It can be done as a standalone visit or alongside a repair.
Related services
Get in touch
Talk to an engineer about your building.
Free, no-obligation surveys and quotes for commercial, public and residential properties. Call us or drop us an email and we will get straight back to you.